Luxurious Bathroom Shower Heads System

This faucet is everything I had hoped for: Easy installation, sensor that works well, even temperature mixing valve. It looks nice in my sink and the flow angle is good.The instructions were good but not great. Installation steps were given in some detail, with diagrams. The manual was clearly translated into English by a non-English-speaker but most of it is clearly understandable. One tantalizing phrase which I wish I understood was this one: "The faucets have self-adjustable sensor eye, the step of adjustment sensor distance is only for reference of customer's special requirements." It sounds from this like there is a way to adjust the sensor eye, but I looked carefully and couldn't find any place in the manual which explains how you would do that, and I didn't see any adjustment knob, dial, screw, etc, anywhere on the sensor or on the valve. I even disassembled the valve box to see if there was an adjustment hidden inside. I'm reasonably sure the manual is incorrect when it says there is an adjustment for this.I have some other doubts as to the accuracy of the manual because in the battery installation step it talks about a "fiber optic cable" and gives a sequence which doesn't make sense. The actual wiring is there is one 2-conductor wire from the battery box to the sensor in the faucet, and another 2-conductor wire from the sensor to the valve. No fiber optics, and I can't see how the sequence of connecting the battery and connecting the valve would make any difference.The installation of the faucet is as follows: The faucet itself is installed in the sink using a base plate on top (including gasket) and a rubber washer, metal washer and nut on the bottom, just like any faucet. The difference is there is an extra wire coming down. The flex hose to the faucet and the wire to the faucet are both connected to a gray box about 8x13cm and 6cm deep which is mounted on the wall below the sink with two drywall anchors and contains the valve and batteries. For cold-water-only installation, a customer-supplied hose runs to the valve inlet at the side of the box. For installations with both cold and hot water coming in, a mixing valve is attached to the side of the gray box and two customer-supplied hoses run to the cold and hot inlets of the mixing valve. Note that the hole in the sink has to be big enough to accommodate the water inlet as well as the wire to the battery and valve, so a hole just big enough for the water alone won't do it.The product uses 4 AA batteries which are stored in a watertight plastic box inside the gray box containing the valve. To replace the batteries, you unclip the cover of the battery compartment, pull out the watertight box, use a screwdriver to remove a screw to open the watertight box, replace the batteries, then put it back together. This is not difficult but can be an awkward reach far back under the sink. The product description says the 4 AA batteries should last 2 years at 200 cycles per day. I didn't test this of course.A 6V AC adaptor is provided which allows the sensor and valve to run off AC power. The connector allows both the battery and the AC adapter power to be connected in parallel, so if the AC fails the batteries continue to run the sensor and valve. I did not try running it using the AC power without batteries installed.There is a particle filter provided on the valve inlet, which is built into the valve in the grey box. The instructions show this should be cleaned with what looks like it might be a toothpick or similar (it is hard to see). The mixing valve also has water filters on each inlet. These are built into the washers, so they are easy to remove and clean.The mixing valve consists of a one-way valve on each inlet that also acts a bit like a pressure regulator, with a central valve that controls which side gets the most flow: Turn it 1/4 turn clockwise and you get all cold water. Turn it 1/4 turn counterclockwise and you get all hot water. In the middle you get a mixture. When installed onto the gray box the valve faces out so it is not difficult for end-users to adjust the temperature mixing. Obviously since this is not thermostatically controlled, a consistent output temperature depends on consistent input temperatures.This is a nice faucet. I hesitated between 4 and 5 stars because of the instruction manual deficiencies, but decided it is a nice enough product to rate 5 stars even though it was not perfect.

This is a great find as I live in a place with very hard water which my hair and skin definitely does not prefer. This is the ideal size for my shower aesthetically and functionally, and installation is super easy basically rinsing it so the filter runs clear and just screwing it on (filter already contained inside the unit) It does not give information on precisely How you Remove the filter, and where to get a new one! I am hoping since this is a new product, that info with the product would be forthcoming (or perhaps this is some standard size product I need to look for on my own)Either way I am happyfor the benefits of this for now!

Decent chrome fitting. The internal hex shape makes it easy to screw in without marring the finish. Quality of the fitting seems really good. All metal. The escutcheon flange is treaded, so you are limited to how far down the pip it will go. And close to the end it will start exposing the threads.

Very good quality

The media could not be loaded.

The best thing about this shower handle mount? Not plastic and no adhesives! Ok. So installation is going to be of a more permanent type, but quality over quantity is my personal choice. Those plastic holders are one angry morning away from catastrophic failure. I’m sure this one could outlast at least 3 or four of my spirited handle returns before failure… but when it looks this good, how could you be mad? Great looking bronze/gold finish. Trim ring stays in place. Comes with everything you need to install. Pivot adjustment is smooth and has the ability to adjust the tension. Description states 360° adjustable but seems to only have about 45° of front to back tilt, which is plenty. Anything more and the shower wand will fall out. Side to side is 360° spin. For standard shower wands on a hose. Designed to work with 1/2” NPT outlet with a solid mounting point, at least that’s what the provided 1/2” male NPT to male G 1/2” adapter appears to be for. Drawing shows item as just a 1/2” G thread (no taper, o-ring style).

I have a lake house and a recent project was upgrading the bathroom. Fortunately, the shower is just a year or two old and still in tip top shape. What I wanted, however, was to add some body spray jets. That's where this product from Cascada Showers comes in. They're a well made shower jet made of high quality brass in a great looking Polished Gold color. I installed a few of these myself but I have considerable experience with bathroom hardware projects. If you're not as experienced, I'd recommend hiring a professional who will do it quickly and do it right. The jets work great with good water pressure and an adjustable spray direction. Solid product at a decent price point. Recommended!

I have body jets in my shower and it is always such a pain to move them to where I want the water to go. With this one, the jets can more easily be diverted to where I want them as it tilts up and down and side to side. A much smarter design. Has a nice gold finish for an accent in the shower.

Like the flow and the spray pattern of this hand held shower wand. The color matches my decor, I ordered the brushed nickel from cascada. It was easy to install. The shower sprayer is light weight.

This 4" shower jet is the real deal. The small size is deceiving, as it's surprisingly heavy and has the weight of a full-size shower head. The size is perfect to fill in a cold spot to one side of my shower, and this has impressive water pressure for such a tiny jet. It doesn't have any settings to adjust the pressure or style of water expression, but it's excellent in my opinion.

The Cascada 4-inch square body spray shower head really surprised me with its performance and style. Though small in size, it delivers a powerful and evenly distributed spray thanks to its 25 built-in nozzles. The brushed gold finish adds a luxurious touch to my shower setup and perfectly complements other modern fixtures. It's solidly built—feels durable in hand—and the wall-mount design was easy to install. I also appreciate that it's adjustable, allowing me to direct the spray exactly where I need it. It’s a small detail that makes a big difference in the overall shower experience. Great upgrade for anyone looking to add a spa-like feel to their bathroom!

I installed this waterfall shower head into my small bathroom one month ago. It elevated my shower experience. The gold matches the bathroom trim. I have been using it for a month now and I love how the water fall feels during my shower. It took me minutes to install. I used some plumbing tape on the end of the pipe to prevent leaks. The downside is that if you have a tub spout you will need to buy that fixture separately. Otherwise it is a fantastic upgrade for a shower.

Really nice showerhead. No it isn't cheap, but I feel I have still gotten a good deal. I have tried so many over the years. All of the fancy varieties, but they usually are made of resins and plastics...and simply don't last.This is the showerhead you won't need to replace. Pretty much everything except the nozzles are made of brass.It has a real heft in the hand.Most importantly for me is the back of the unit. It has small hex bolts around the edges. I can take the entire unit apart with an allen key. Most of my other past showerheads are not designed to be taken apart...chance are I will break something. Not this one. I have good clean well water, but also high in minerals. If I cannot take it apart...any head is destined to clog up. Love this design.All the parts are well made and the faceplate is also quite solid. I like that they signed their name...they are proud of this and they should be.Spend the coin and you will get a top quality showerhead...for many years to come.Looks great as well...to me.Recommended!

The media could not be loaded.

This set looks really nice and the brushed gold has a great finish. Since I'm replacing an existing shower head I haven't been able to switch out the wall plate just yet, but the shower head itself was really easy to install.

I've had 4 of these installed at our club for 2 months now and they are functioning perfectly. I would buy again.

This automatic faucet works great. I have tried many others for my small business and nore were as reliable as this one. I actually have 2 of these now and they are great.